InspectAPedia ^®

This article describes brick wall lining or "insulation" in buildings, why it was used, what problems may occur, and the inspection methods and clues to detect brick lined walls in older homes (sometimes called Nogging) and discusses the implications of brick wall liners in buildings. Non-structural bricks were used to line the exterior walls in some pre-1900 wood frame buildings primarily an air infiltration or wind barrier, possibly as "insulation" or for thermal mass, and possibly as a "sound proofing" method. Readers should also see THERMAL MASS in BUILDINGS.

Often these homes were built with balloon stud framing, no exterior sheathing (they used diagonal bracing), and exterior clapboards right on the studs. In homes framed in this manner, if the exterior wall cavities were left empty, the walls were drafty and uninsulated. Some homes, such as the Weisman home in Montgomery NY (shown above) and another home photographed by Arlene Puentes (shown below), were built with brick-lined walls, bricks being mortared in between the studs on all floors and even extending into the attic.

Other benefits of this design included fire stopping effects and added thermal mass to the building, making temperature changes less rapid and thus the house more comfortable. The presence of brick in wood frame wall cavities, such as in the photograph shown at the top of this page (Courtesy Joe and Beth Weisman) may help determine the age of a building.

The condition of the brick "nogging" may also be an important indicator of the building leak history. © Copyright 2009 Daniel Friedman, Arlene Puentes, All Rights Reserved. Information Accuracy & Bias Pledge is at below-left. Use links at the left of each page to navigate this document or to view other topics at this website. Green links show where you are in our document or website.

Brick Wall Lining in Older Homes

Brick wall "insulation" or brick nogging may be found in wood framed buildings built up to about 1900. Usually these homes have exterior clapboards and interior plaster walls.

An owner of such a home usually finds out about the brick in the home walls at the first renovation or wiring or plumbing project. But a home inspector and home buyer might also be able to detect brick-lined walls and should be interested in what this construction method might mean to the new owner.

These bricks are not structural, and they were simply mortared in place between wood framed wall studs and rested on the sill plates of each floor. It would be unusual to find brick wall linings in interior walls unless at one time the "interior" wall was at one time a building exterior wall structure.

Brick Nogging was generally not intended to be exposed to view, and served the purpose of blocking wind that blew through older homes constructed without an exterior sheathing - clapboards were nailed directly to the structural frame. Typical wall construction was stud framing, 16" o.c., diagonal wood bracing in walls, clapboard exterior, rough masonry wall filler on all floors and extending into the attic. Interior walls were covered by plaster on wood lath.

Opening walls filled with brick nogging or other masonry will often reveal rough and varying styles of masonry (as it was not intended to be seen) that went in fast. The masons may have used a variety of bricks and rubble. I [DF] suspect that this construction method may have been adopted by builders who had observed the short life and pest infestation problems that followed colonial and later attempts at wall insulation using natural materials like straw and corncobs.

Websters Dictionary gives this definition: "Nogging: (?), n. Rough brick masonry used to fill in the interstices of a wooden frame, in building."
Wordnet Dictionary gives this similar definition: "Noun 1. nogging - rough brick masonry used to fill in the gaps in a wooden frame". "Nogging" is a term also used by some to describe exposed brick lining in timber framed walls in which the brick is left in view on the building exterior for aesthetic reasons.

Because brick (or other masonry) placed in building cavities as a wind barrier and thermal mass source was in that use not intended to be exposed, you can expect to see the workmanship quite rough in appearance and inconsistent from one building area to another (as any and various masonry material at hand might be used) compared with masonry intended to be left exposed to view.

Some Considerations for Homes with Brick Lined Walls - Brick Nogging

• House Age: Brick nogging helps set a possible age for the home. Houses built between 1810 and 1900, or perhaps earlier may have brick-lined walls. I [Friedman] found brick nogging lining the walls of a 1790 house in Poughkeepsie NY. So finding bricks in your house walls is often a clue about when it was built.
• Insulating Value of Brick Wall Lining: Brick has an "R" value estimated at about 0.11", so a brick lined wall has an R-value of something like R1 overall (including the wood siding and interior plaster) - pretty low compared with modern R11-R20 walls. Adding conventional insulation such as fiberglass batts, blown-in fiberglass, or blown-in cellulose or foam (to save heating and cooling costs) are not an option unless walls are stripped from inside or outside first, and bricks removed. In an extensive old house renovation, if the project includes replacing exterior siding or interior wall surfaces, and in homes where accurate historic preservation of original construction materials and details is not a requirement, it is common to remove all of the wall-lining bricks in order to substitute a more effective insulating material. Owners who have taken this step (such as the Weismans) report a significant reduction in home heating costs.
• Weight of Brick-Lined Walls: Alan Carson, (Carson Dunlop Associates, Toronto) estimates that weight would be about 400 lb. per stud cavity per floor. (Clay bricks weigh about 150 lb./cu. ft.). If the structure is damaged by rot or insects, or modified by "remodeling" there is risk that the added weight of bricks in upper floor walls could require additional support. Beware of remodeling on lower floors which includes the removal of bricks in the wall cavities - it may be necessary to add support to be certain that weight of brick lining upper floor walls does not cause a structural problem for the lower floors.
• Brick Wall Liners and Fire Safety: If the building was framed using balloon framing rather than platform framing it may be necessary to add fire blocking if bricks are removed since you may have removed what amounted to fire-blocking in the wall cavities.
• Brick Lined Wall Collapse Warning: Joe and Beth Weisman pointed out at their website [References below] that when removing exterior siding [or interior plaster] one should be careful to watch out for falling bricks. In their renovation one wall dumped quite a few bricks on the ground when it was opened. Puentes points out that in earthquake prone areas, "hidden" brick or other masonry wall lining could fall into an upper room and perhaps through a ceiling into a room below, making this construction method an additional safety concern for houses in earthquake zones. [We don't know if this method has been used in earthquake areas.]
• Brick Walls, Condensation, and Mold: Brick wall lining may increase condensation on the interior of some exterior walls and could be a dampness or mold issue. You may see evidence of this as mold behind pictures that have been hung on exterior walls for some time. You'll also see this in solid-masonry homes.
• Electical Wiring: Running new electrical circuits in exterior walls will encounter the brick lining which may need to be removed in some cases (or run wires behind floor baseboards or in other chases). Carson wondered if the absence of electrical wiring (seen as no outlets nor switches) in the walls of an older building might suggest brick lining.

Where Will You Find Clues Suggesting the Presence of Brick Lined Walls

• Age of the home: if the home was built before 1900 and is a wood frame structure, especially in cold climates where people care more about wind blowing through walls, brick nogging may have been used.

• This photo shows the wall-cavity or interior surface of the exterior clapboard sheathing used on this home. The draftiness of walls constructed in this manner was a reason that some builders used brick wall lining as not only insulation but as "wind barrier". I f you look closely at the exposed side of the clapboards in this photograph where some wall lining bricks have conveniently fallen away, you'll see circular saw cut marks - an indicator that this house is not one of the older instances of brick wall lining. I estimate that this house dates from 1890. New York State had circular saw lumber mills sooner than some other states, and saw marks are not a precise dating method, but had this been a home from 1840-1850 we may have seen that the saw blade had left straight blade marks across the clapboard - indicating a power-operated vertical "pit saw." Had the saw blade marks been straight but alternating in a tight "X" pattern across the clapboard the board would have been cut on a hand-operated pit saw, and this would be a still-older home.

• In the basement, bricks may be visible between floor joists sitting atop the building sills, especially in balloon-framed homes. Arlene Puentes' photograph shows how subtle this clue may be as very little brick may be visible from the basement.

• In the living area - bricks may be discovered in wall cavities during renovations or remodeling
• Mold on Walls: while certainly not a sure bet, the presence of mold behind wall hangings occurring on exterior walls may indicate the effects of brick lined wall cavities. The brick lining can mean that the surface of this wall stays cooler longer and has more condensation on the wall surface than will be seen on the surface of interior walls.
• Sagging at Sills: At the interior side of exterior walls, usual degrees of sill or rim joist crushing in areas of rot or insect damage could include the added effects of the extra weight of bricks in the building exterior walls.

• In the attic - bricks may be visible between wall studs extending up into the attic. In this photograph of a brick-lined wall you can see that some of the bricks have fallen out of the wall cavity and onto the attic floor. This is not itself a structural problem but it may indicate a history of roof leaks at this spot. Roof leaks may in turn track to rot or insect damage. Based on this theory and buttressed by leak stains visible in the photograph, I'm guessing that these fallen bricks were on an eaves wall not a gable end wall. We discuss this further below at "Repairs".

• Arlene's photograph of this brick-lined wood framed wall in an attic shows the diagonal bracing commonly used in this generation of wood frame brick-lined construction. The care with which the mason filled-in with brick and mortar even around the diagnoal bracing confirms the intention of this usage as an air barrier.

• Exterior Renovations: From the exterior - bricks may be visible if siding is removed for repairs or other building work

What to do if Portions of Your Brick Wall Lining Has Fallen into the Attic

• Clean up the fallen masonry and debris.
• Diagnose the reason that the bricks fell into the attic: the masonry wall filler may have been damaged by water from roof leaks or ice dam leaks if the home is in a northern climate. If this is the case you'll want to be sure you've corrected the cause of water leakage. If the brick collapse is traced to water leaks be sure to also look for evidence of structural rot of nearby wood framing members, and be alert for evidence of insect damage since leaks can attract carpenter ants or termites into a building, including an attic.
• Consider rebuilding the brick liner in the wall cavity if you are not planning to renovate the area. Use soft mortar as was used originally. This option makes sense if only one or two bricks have fallen from place.
• Alternatively, use modern insulation - especially where lots of wall-lining bricks have fallen or are loose and appear about to fall, insulate the wall empty wall cavity with other insulating material such as fiberglass batts.

References & Credits for this Brick Wall Lining (Brick Nogging) Article

Share this Article      

...

Technical Reviewers & References

Search InspectAPedia

• Daniel Friedman - principal author/editor of the InspectAPedia^® Website
• InspectAPedia Bookstore lists recommended books, organized by topic & available for purchase. Most of our articles also include a list of recommended books for the specific article topic as well as other references, and information sources.
• Critique, contributions wanted: Contact Us to suggest corrections or additions to articles at this website, and if you wish, to receive online listing and credit as a contributor. Particular thanks are due to the many experts and also consumers who read and critique technical articles at InspectAPedia.com.
• Additional technical contributors & reference sources for this article are listed below.

Use links just below or at the left of each page to navigate this document or to view other topics at this website. Green links show where you are in our document or website.

INSULATION & VENTILATION INSPECTION & IMPROVEMENT
INTERIORS of BUILDINGS
ACOUSTICAL SEALANTS
AGE of a BUILDING - how to determine
AIR BYPASS LEAKS
AIR LEAK DETECTION TOOLS
AIR LEAK MINIMIZATION
AIR SEALING STRATEGIES
ANIMAL ALLERGENS
ASBESTOS IDENTIFICATION IN BUILDINGS
ATTIC LEAKS, CONDENSATION & ATTIC MOLD
ATTIC VENTILATION
BASEMENT HEAT LOSS
BASEMENT LEAKS Moisture or Mold
BASEMENT WATERPROOFING
BATHROOM VENTILATION
BLOWER DOORS & AIR INFILTRATION
BRICK LINED WALLS
BUCKLED FOUNDATIONS due to INSULATION?
CATHEDRAL CEILING INSULATION
CHIMNEY INSPECTION DIAGNOSIS & REPAIR
COMBUSTION AIR for TIGHT BUILDINGS
CRAWL SPACES
DEW POINT CALCULATION for WALLS
DEW POINT TABLE - CONDENSATION POINT GUIDE
ELECTRICAL INSPECTION, DIAGNOSIS, REPAIR
ENERGY SAVINGS in BUILDINGS
ENERGY SAVINGS PRIORITIES
ENERGY SAVINGS RETROFIT CASE STUDY
ENERGY SAVINGS RETROFIT LEAK SEALING GUIDE
ENERGY SAVINGS RETROFIT OPTIONS
ENVIRONMENTAL HAZARDS
FIBERGLASS INSULATION
FIBERGLASS HAZARDS
FIBERGLASS MOLD
FIREPLACE Damage & Unsafe Hearths - Settlement
FLAT ROOF MOISTURE & CONDENSATION
FLOOD DAMAGE ASSESSMENT, SAFETY & CLEANUP
FLOODS IN BUILDINGS-mold
FLOORING TYPES & DEFECTS
FOUNDATION WATERPROOFING
FRAMING DETAILS for BETTER INSULATION
FRAMING DETAILS for DOUBLE WALL HOUSES
FREEZE-PROOF A BUILDING
HEAT LOSS in BUILDINGS
HEAT LOSS DETECTION TOOLS
HEAT LOSS INDICATORS
HEAT LOSS R U & K VALUE CALCULATION
Heat Tapes: Use on Roofs for Ice
HEATING COST SAVINGS METHODS
HOUSEWRAP AIR & VAPOR BARRIERS
HUMIDITY LEVEL TARGET
ICE DAM PREVENTION
Ice Dams: Comparing Two Houses
INSULATION CHOICES
INSULATION FACT SHEET- DOE
INSULATION IDENTIFICATION GUIDE
INSULATION LOCATION for BASEMENTS
INSULATION LOCATION for CAPES, CRAWLSPACES
INSULATION for GREENHOUSE or SOLARIUM
INSULATION MATERIAL IDENTIFICATION GUIDE
INSULATION MOLD
INSULATION R-Values & Properties
INSULATION & VENTILATION INSPECTION & IMPROVEMENT
  ATTIC CONDENSATION CAUSE & CURE
  Air Bypass Leaks, Thermal Tracking
  Blocked Soffit Intake Vents
  BRICK VENEER WALL INSULATION
  CATHEDRAL CEILING INSULATION
  ENERGY SAVINGS in BUILDINGS
  ENERGY SAVINGS PRIORITIES
  ENERGY SAVINGS RETROFIT CASE STUDY
  ENERGY SAVINGS RETROFIT LEAK SEALING GUIDE
  ENERGY SAVINGS RETROFIT OPTIONS
  FRAMING DETAILS for BETTER INSULATION
  FRAMING DETAILS for DOUBLE WALL HOUSES
  Inspect Attics for Moisture or Mold
  Inspect Basements for Moisture or Mold
  Inspect Building Exterior
  Inspect the Ridge Vent System from the Attic
  Inspect the Soffit Vent System from the Attic
  Insulation Air & Heat Leaks
  INSULATION R-Values & Properties
  Insulation Values of Log Home Walls
  POLYISOCYANURATE FOAM INSULATION
  POLYSTYRENE FOAM INSULATION
  RADIANT BARRIERS
  RIGID FOAM USE INDOORS
  Urea Formaldehyde Foam Insulation UFFI
  URETHANE FOAM Deterioration, Outgassing
  Vermiculite Insulation
LOG HOME GUIDE
MOBILE HOME INSPECTIONS
MOISTURE CONTROL in BUILDINGS
Mold Growth Resistance of Foam Insulation
MOLD INFORMATION CENTER
ODORS & SMELLS DIAGNOSIS & CURE
PAINT FALURE, DIAGNOSIS, CURE, PREVENTION
PLASTER & BEAVERBOARD & DRYWALL
RADIANT BARRIERS
RADIANT HEAT
RADIANT HEAT Floor Mistakes to Avoid
RADIANT SLAB FLOORING CHOICES
RADIANT SLAB TUBING & FLUID CHOICES
ROOF VENTILATION SPECIFICATIONS
ROT, FUNGUS, TERMITES
  TERMITE SHIELDS vs TERMITICIDE
ROT, TIMBER FRAME
SAFETY HAZARDS & INSPECTIONS
SEARS KIT HOUSES
SOLAR ENERGY SYSTEMS
  PASSIVE SOLAR DESIGN METHOD
  PASSIVE SOLAR HEAT PERFORMANCE
  PHOTOVOLTAIC POWER SYSTEMS
  SLAB INSULATION, PASSIVE SOLAR
  SOLAR COLLECTOR AIR or GAS COLLECTION
  SOLAR COLLECTOR FILMS
  SOLAR COLLECTOR WOOD HOUSINGS
  SOLAR HEATING SYSTEMS
  SOLAR HOT WATER HEATERS
  SOLAR HOUSE EVALUATION
SOUND CONTROL in BUILDINGS
STAIN DIAGNOSIS
STAIRS, RAILINGS, LANDINGS, RAMPS
STUCCO OVER FOAM INSULATION
STRUCTURAL INSPECTIONS & DEFECTS
SUMP PUMPS GUIDE
THERMAL EXPANSION of MATERIALS
THERMAL MASS in BUILDINGS
THERMAL MASS in UPSTAIRS
THERMAL TRACKING Indicates Heat Loss
  Ceiling Thermal Tracking Marks
  Wall Thermal Tracking Stains
  Floor Carpet Thermal Tracking Stains
  Air Bypass Leaks Marks on Insulation
  Thermal Tracking to Diagnose IAQ
  Stains HVAC Supply Registers
  Pet Stains on Floors
  Pet Stains on Walls
  Human Occupant Stains on Walls
  Stains from Candles, Woodstoves, Fireplaces
  Other Stains on Indoor Walls & Ceilings
  What to Do About Thermal Tracking
VAPOR BARRIERS & AIR SEALING at BAND JOISTS
VAPOR BARRIERS & CONDENSATION in BUILDINGS
VAPOR BARRIERS & HOUSEWRAP
VAPOR CONDENSATION & BUILDING SHEATHING
VENTILATION in BUILDINGS
WATER ENTRY in BUILDINGS
WIND TURBINES
WINDOWS & DOORS
WINTERIZE A BUILDING
WOOD Burning Heaters Fireplaces Stoves

• Arlene Puentes, a licensed home inspector, educator, and building failures researcher in Kingston, NY. Photographs © Arlene Puentes 2006 All Rights Reserved. Text © Daniel Friedman Arlene Puentes 2007-2006 All Rights Reserved.
• Technical contributions and review: Alan Carson, Carson Dunlop Associates, Toronto, Ontario. Al Carson is a building failures researcher, educator, and a past president of ASHI, the American Society of Home Inspectors.
• Photo contributions: Joe and Beth Weisman, who have been renovating a brick-insulated house in Montgomery, NY were kind enough to share some of their website's photos for this article. Individual photo sources are cited in the text above.

Books & Articles on Building & Environmental Inspection, Testing, Diagnosis, & Repair

• Our recommended books about building design, inspection, and repair, and about indoor environment testing, diagnosis, and cleanup are at the InspectAPedia Bookstore.
• ...

More Information on Building Diagnostic Inspections and Repairs

More on hidden and exposed wall brick or stone or other fill-in materials on old buildings:

• Brick nogging used as soundproofing is mentioned in this article on Popular Forest
• Brick Nogging, Historical Investigation and Contemporary Repair, Construction Specifier, April 2006. Historical use of brick in timber-framed buildings, drawing on the investigations of the Kent Tavern in Calais, VT. "Brick nogging is a European method of construction which was brought to the new world in the early-nineteenth century. It was a common construction method that employed masonry as infill between the vertical uprights of wood framing." -- quoting the web article review.
• Photo of very rough in-wall brick nogging at an architects website
• Nogging: See this photo of exposed bricks on a building exterior on a building exterior in Canada. [Thanks to Carson Dunlop, Toronto - see References below].
• Piquet Wall Construction: See this photo of piquet wall construction - involving timber-framed wall construction with long top girts, diagnoal timber bracing, and small diameter logs placed vertically along with concrete chinking to fill in the wall plane.
• Rubblestone Wall Filler: See this Lartigue House using exterior-exposed rubblestone filler between vertical timbers of a post and beam-framed Canadian building.
• These photos are from an 18th French fortress in Nova Scotia. See the ( Louisburg Fortress) tourist site.
• Also see the Louisburg research site.

InspectAPedia® Home & Site Map - Building & Environmental Inspection, Testing, Diagnosis, Repair, & Problem Prevention Advice: In-depth research & advice on diagnosing, testing, correcting, & preventing building defects & indoor environmental hazards. Unbiased information, no conflicts of interest.

The Mold Information Center: What to Do About Mold in Buildings, When and How to Inspect for Mold, Clean Up Mold, or Avoid Mold Problems

Use this simple, economical mold test kit by following our instructions on how to collect and mail mold samples to our lab

Environmental Inspection, Testing, & Diagnosis On-Site IAQ, Gas, Air Testing, Mold Investigation, Sick Building Diagnosis, Lab Services, & Remediation Plan Preparation - indoor air quality testing, problem source determination, supporting lab work, written remediation plan addressing removal of environmental and other hazards and prevention of their recurrence.

Building Inspection, Problem Diagnosis, Forensic Investigation & Testing, Repair Consulting

Contact Daniel Friedman for website content suggestions or for fee-paid consulting