InspectAPedia ^®

This chapter "How to Inspect in the Attic or Roof Cavity for Signs of an Under-roof Condensation Problem, is part of our discussion of "Attic Condensation". This article describes inspection methods and clues to detect roof venting deficiencies, insulation defects, and attic condensation problems, in buildings. It describes proper roof ventilation placement, amounts, and other details. Also see CATHEDRAL CEILING INSULATION.

These recommendations are based on 30 years of building inspections, on the observation of the locations of moisture, mold, ice dams, condensation stains, and other clues in buildings, and on the correlation of these clues with the roof venting conditions at those properties. I have also measured changes in airflow, temperature, and moisture before and after installing roof venting.

© Copyright 2009 Daniel Friedman, All Rights Reserved. Information Accuracy & Bias Pledge is at below-left. Use links at the left of each page to navigate this document or to view other topics at this website. Green links show where you are in our document or website.

Inspecting in the Attic or Roof Cavity for Signs of an Under-roof Condensation Problem

After examining the eaves or lower roof edges, look up at the ridge for a continuous opening on either side of the ridge board, providing an exit vent path. On some buildings I've found that a ridge vent was installed but the installer just nailed it over the existing roof sheathing, forgetting to cut the necessary opening. "Spot vents" on lower roof slopes, or power vent fans are not as good a substitute for the year-round passive venting provided by a ridge vent.

You often will see many drip spots on the attic flooring or insulation (Left photo below). This is caused by moisture condensing on the roofing nails and dropping to the surface below. This is sure evidence of a condensation problem. The pattern of drip marks may be remarkably just like the pattern of roof shingle nails which protrude through the roof sheathing.

Winter condensation on the nails, even forming frost in freezing weather, rusts the nails and stains the roof sheathing around them. Frost later melts off of these nails and drips onto the floor below. The pattern may occur more on the cooler or north slope of the roof.

If attic stains are from roof leaks, (right photo above) they will usually be much larger and will appear on the sides of rafters, on larger areas of the roof sheathing, and on larger areas of the attic floor.

If you see evidence of extensive roof leaks or condensation leaks, I'd also check the insulation and the attic side of the ceiling drywall for a hidden mold problem.

If you see condensation drip stains in the attic (left photo above), you'll be confirming what you suspected from outside -- inadequate ventilation.

How to Inspect the Attic for Moisture - Stains Around Roofing Nails

Rust or stains around roofing nails that protrude through the attic sheathing (they're supposed to stick through) are a clear indication of high attic moisture.

Our photograph at above left shows roofing nails protruding through plywood roof sheathing visible in an attic where there is no under-roof condensation or moisture problem.

Our photograph at above right shows roofing nails which have rusted and stained the roof plywood in an attic where indoor moisture has risen through the building to condense on the under-side of the roof.

How to Spot Attic Mold Due to High Attic Moisture or Roof Leaks

These photos show mold on attic surfaces due to high moisture in that area. While many inspectors notice dark mold or mold-suspect material on roof framing or roof sheathing, it is at least as important, and often more important to spot the light-colored molds that may also be present - often these are the more hazardous, particularly if building conditions cause air movement downwards out of the attic into the living space or into an attic-located HVAC duct system.

The brown/black attic mold on plywood in the left-hand photo is easy to spot and is often an allergen or problematic attic fungus like Cladosporium sp., Pithomyces chartarum, Ulocladium sp., or Aureobasidium pullulans but the light colored mold on the tongue-and-groove pine roof sheathing in the right photo was found to be Penicillium sp. which is more likely to be airborne and transmitted in the building.

If you find significant levels or large areas of mold in your attic the mold should be cleaned - that is, removed. Do not rely on magic bullets like sprays alone. The spray approach does not remove the problem mold and it may spread it into otherwise uncontaminated materials like insulation.

Don't tear off the roof over a moldy attic: Unless the mold-causing conditions have also rotted framing or delaminated plywood roof sheathing, structural removal/replacement, such as a roof tear-off are unnecessary and inappropriate. But don't forget that if you see attic mold the insulation or ceiling drywall below may also be moldy.

See How to Find, Test For, & Remove Mold in Attics for details about where and how to look for attic mold and what to do about it.

Share this Article      

...

Technical Reviewers & References

Search InspectAPedia

• Daniel Friedman - principal author/editor of the InspectAPedia^® Website
• Critique, contributions wanted: Contact Us to suggest corrections or additions to articles at this website, and if you wish, to receive online listing and credit as a contributor. Particular thanks are due to the many experts and also consumers who read and critique technical articles at InspectAPedia.com.
• Alan Carson Carson Dunlop Associates, Toronto, Ontario. Mr. Carson is a home inspection professional, educator, researcher, writer, and a principal of Carson Dunlop Associates, a Toronto home inspection and education firm. Mr. Carson is a past president of ASHI, the American Society of Home Inspectors Some great illustrations of the proper under-roof ventilation pathways are offered by Carson Dunlop.
• Mark Cramer Inspection Services Mark Cramer, Tampa Florida, Mr. Cramer is a past president of ASHI, the American Society of Home Inspectors and is a Florida home inspector and home inspection educator. (727) 595-4211 mark@BestTampaInspector.com 11/06 & 12/08
• John Annunziata, P.E. - NY Metro ASHI during informal chapter discussions about roof and attic ventilation options (1986-1996).
• Technical reviewers are invited to comment or ask questions - contact us

Use links just below or at the left of each page to navigate this document or to view other topics at this website. Green links show where you are in our document or website.

INTERIORS of BUILDINGS
AIR BYPASS LEAKS
AIR LEAK DETECTION TOOLS
AIR LEAK MINIMIZATION
AIR SEALING STRATEGIES
BATHROOM VENTILATION
BASEMENT WATERPROOFING
BLOWER DOORS & AIR INFILTRATION
BRICK LINED WALLS
BUCKLED FOUNDATIONS due to INSULATION?
CATHEDRAL CEILING INSULATION
FREEZE-PROOF A BUILDING
ATTIC CONDENSATION CAUSE & CURE
Air Bypass Leaks, Thermal Tracking
Blocked Soffit Intake Vents
CATHEDRAL CEILING INSULATION
Comparing Two Houses
Heat Tapes: Use on Roofs for Ice
Inspect Attics for Moisture or Mold
Inspect Basements for Moisture or Mold
Inspect Building Exterior
Inspect the Ridge Vent System from the Attic
Inspect the Soffit Vent System from the Attic
ROOF VENTILATION SPECIFICATIONS
Roof Venting: Intake - Outlet Area Ratios
Roof Venting: Proper Locations
Roof Venting: Both Ridge & Eaves Venting Needed
Roof Venting: Eaves Intake if no Overhang
Roof Venting: Soffit Intake Vent-Continuous
Roof Venting: Un-Vented Roof Solutions
ROOF VENTING ENERGY SAVING DETAILS
HEAT LOSS: How to Calculate Heat Loss in a Building
HOUSEWRAP AIR & VAPOR BARRIERS
HUMIDITY LEVEL TARGET
ICE DAM PREVENTION
INSULATION INSPECTION & IMPROVEMENT
THERMAL TRACKING & HEAT LOSS

Books & Articles on Building & Environmental Inspection, Testing, Diagnosis, & Repair

• Our recommended books about building design, inspection, and repair, and about indoor environment testing, diagnosis, and cleanup are at the InspectAPedia Bookstore.
• "Weather-Resistive Barriers", how to select and install housewrap and other types of weather resistive barriers, U.S. DOE
• ...

More Information on Building Diagnostic Inspections and Repairs

More Reading about Dealing with Attic Mold, Identifying, Removing, and Preventing Mold in Attics

Be sure to review HOW TO FIND MOLD: How to Inspect Homes and Other Buildings for Mold - the Basics of How to Find Problem Mold Indoors in our Mold Action Guide. Here are other articles that will be helpful in evaluating attic mold presence, causes, and cures:

• What Mold and Allergens Look Like: mold identification photos to help identify mold - choosing what to sample in buildings
• How to Clean Moldy Wood Framing & Sheathing How to clean/seal mold from/on exposed lumber or plywood subfloor or roof sheathing indoors - some suggestions based on our field and laboratory research
• Lighting, proper use of: proper aiming of a good flashlight can disclose hard to see but toxic light or white mold colonies on walls.
• Mold spores in the Home - a Photo ID Library for detection and identification of mold allergens.
• How to Find and Test For Mold in Buildings A "how to" photo and text primer on finding and choosing the right spots to test for mold in buildings
• Stuff that is not mold but is often mistaken for it - things you may not want to test. Also, not all "black mold" is toxic - here are examples of harmless black mold.
• Simple Adhesive Tape Sampling of Moldy Surfaces - how to send a mold sample to our lab
• Mold Sampling Methods in the Indoor Environment - In-depth article: detailed critique of popular mold testing methods - Is your mold test kit worth the bother?
• Humidity: What indoor humidity should we maintain in order to avoid a mold problem?
• Mold-Resistant Building Practices, advice from an expert on how to prevent mold after a building flood and how to prevent mold growth in buildings by selection of building materials and by anti-mold construction details.

InspectAPedia® Home & Site Map - Building & Environmental Inspection, Testing, Diagnosis, Repair, & Problem Prevention Advice: In-depth research & advice on diagnosing, testing, correcting, & preventing building defects & indoor environmental hazards. Unbiased information, no conflicts of interest.

The Mold Information Center: What to Do About Mold in Buildings, When and How to Inspect for Mold, Clean Up Mold, or Avoid Mold Problems

Use this simple, economical mold test kit by following our instructions on how to collect and mail mold samples to our lab

Environmental Inspection, Testing, & Diagnosis On-Site IAQ, Gas, Air Testing, Mold Investigation, Sick Building Diagnosis, Lab Services, & Remediation Plan Preparation - indoor air quality testing, problem source determination, supporting lab work, written remediation plan addressing removal of environmental and other hazards and prevention of their recurrence.

Building Inspection, Problem Diagnosis, Forensic Investigation & Testing, Repair Consulting

Contact Daniel Friedman for website content suggestions or for fee-paid consulting